9.3 Distribution needed for hypothesis testing

Earlier in the course, we discussed sampling distributions. Particular distributions are associated with hypothesis testing. Perform tests of a population mean using a normal distribution or a Student's t -distribution . (Remember, use a Student's t -distribution when the population standard deviation is unknown and the distribution of the sample mean is approximately normal.) We perform tests of a population proportion using a normal distribution (usually n is large or the sample size is large).

If you are testing a single population mean , the distribution for the test is for means :

$\overline{X}~N\left({\mu }_X,\frac{{\sigma }_X}{\sqrt{n}}\right)$ or $t_{df}$

The population parameter is μ . The estimated value (point estimate) for μ is $\overline{x}$ , the sample mean.

If you are testing a single population proportion , the distribution for the test is for proportions or percentages:

$P^{\prime }~N\left(p,\sqrt{\frac{p\cdot q}{n}}\right)$

The population parameter is p . The estimated value (point estimate) for p is p′ . p′ = $\frac{x}{n}$ where x is the number of successes and n is the sample size.

Assumptions

When you perform a hypothesis test of a single population mean μ using a Student's t -distribution (often called a t-test), there are fundamental assumptions that need to be met in order for the test to work properly. Your data should be a simple random sample that comes from a population that is approximately normally distributed . You use the sample standard deviation to approximate the population standard deviation. (Note that if the sample size is sufficiently large, a t-test will work even if the population is not approximately normally distributed).

When you perform a hypothesis test of a single population mean μ using a normal distribution (often called a z -test), you take a simple random sample from the population. The population you are testing is normally distributed or your sample size is sufficiently large. You know the value of the population standard deviation which, in reality, is rarely known.

When you perform a hypothesis test of a single population proportion p , you take a simple random sample from the population. You must meet the conditions for a binomial distribution which are: there are a certain number n of independent trials, the outcomes of any trial are success or failure, and each trial has the same probability of a success p . The shape of the binomial distribution needs to be similar to the shape of the normal distribution. To ensure this, the quantities np and nq must both be greater than five ( np >5 and nq >5). Then the binomial distribution of a sample (estimated) proportion can be approximated by the normal distribution with μ = p and $\sigma =\sqrt{\frac{pq}{n}}$ . Remember that q = 1 – p .

Chapter review

In order for a hypothesis test’s results to be generalized to a population, certain requirements must be satisfied.

When testing for a single population mean:

1. A Student's t -test should be used if the data come from a simple, random sample and the population is approximately normally distributed, or the sample size is large, with an unknown standard deviation.
2. The normal test will work if the data come from a simple, random sample and the population is approximately normally distributed, or the sample size is large, with a known standarddeviation.

When testing a single population proportion use a normal test for a single population proportion if the data comes from a simple, random sample, fill the requirements for a binomial distribution, and the mean number of success and the mean number of failures satisfy the conditions: np >5 and nq > n where n is the sample size, p is the probability of a success, and q is the probability of a failure.

Formula review

If there is no given preconceived α , then use α = 0.05.

Types of hypothesis tests

• Single population mean, known population variance (or standard deviation): Normal test .
• Single population mean, unknown population variance (or standard deviation): Student's t -test .
• Single population proportion: Normal test .
• For a single population mean , we may use a normal distribution with the following mean and standard deviation. Means: $\mu ={\mu }_{\overline{x}}$ and ${\sigma }_{\overline{x}}=\frac{{\sigma }_x}{\sqrt{n}}$
• A single population proportion , we may use a normal distribution with the following mean and standard deviation. Proportions: µ = p and $\sigma =\sqrt{\frac{pq}{n}}$ .