<< Chapter < Page Chapter >> Page >

Measuring rates of reaction

How the rate of a reaction is measured will depend on what the reaction is, and what product forms. Look back to the reactions that have been discussed so far. In each case, how was the rate of the reaction measured? The following examples will give you some ideas about other ways to measure the rate of a reaction:

  • Reactions that produce hydrogen gas: When a metal dissolves in an acid, hydrogen gas is produced. A lit splint can be used to test for hydrogen. The 'pop' sound shows that hydrogen is present. For example, magnesium reacts with sulfuric acid to produce magnesium sulphate and hydrogen. M g ( s ) + H 2 S O 4 M g S O 4 + H 2
  • Reactions that produce carbon dioxide: When a carbonate dissolves in an acid, carbon dioxide gas is produced. When carbon dioxide is passes through limewater, it turns the limewater milky. This is a simple test for the presence of carbon dioxide. For example, calcium carbonate reacts with hydrochloric acid to produce calcium chloride, water and carbon dioxide. C a C O 3 ( s ) + 2 H C l ( a q ) C a C l 2 ( a q ) + H 2 O ( l ) + C O 2 ( g )
  • Reactions that produce gases such as oxygen or carbon dioxide: Hydrogen peroxide decomposes to produce oxygen. The volume of oxygen produced can be measured using the gas syringe method ( [link] ). The gas collects in the syringe, pushing out against the plunger. The volume of gas that has been produced can be read from the markings on the syringe. For example, hydrogen peroxide decomposes in the presence of a manganese(IV) oxide catalyst to produce oxygen and water. 2 H 2 O 2 ( a q ) 2 H 2 O ( l ) + O 2 ( g )
    Gas Syringe Method
  • Precipitate reactions: In reactions where a precipitate is formed, the amount of precipitate formed in a period of time can be used as a measure of the reaction rate. For example, when sodium thiosulphate reacts with an acid, a yellow precipitate of sulfur is formed. The reaction is as follows: N a 2 S 2 O 3 ( a q ) + 2 H C l ( a q ) 2 N a C l ( a q ) + S O 2 ( a q ) + H 2 O ( l ) + S ( s ) One way to estimate the rate of this reaction is to carry out the investigation in a conical flask and to place a piece of paper with a black cross underneath the bottom of the flask. At the beginning of the reaction, the cross will be clearly visible when you look into the flask ( [link] ). However, as the reaction progresses and more precipitate is formed, the cross will gradually become less clear and will eventually disappear altogether. Noting the time that it takes for this to happen will give an idea of the reaction rate. Note that it is not possible to collect the SO 2 gas that is produced in the reaction, because it is very soluble in water.
    At the beginning of the reaction beteen sodium thiosulphate and hydrochloric acid, when no precipitate has been formed, the cross at the bottom of the conical flask can be clearly seen.
  • Changes in mass: The rate of a reaction that produces a gas can also be measured by calculating the mass loss as the gas is formed and escapes from the reaction flask. This method can be used for reactions that produce carbon dioxide or oxygen, but are not very accurate for reactions that give off hydrogen because the mass is too low for accuracy. Measuring changes in mass may also be suitable for other types of reactions.

Get Jobilize Job Search Mobile App in your pocket Now!

Get it on Google Play Download on the App Store Now




Source:  OpenStax, Siyavula textbooks: grade 12 physical science. OpenStax CNX. Aug 03, 2011 Download for free at http://cnx.org/content/col11244/1.2
Google Play and the Google Play logo are trademarks of Google Inc.

Notification Switch

Would you like to follow the 'Siyavula textbooks: grade 12 physical science' conversation and receive update notifications?

Ask