1. Home
  2. College physics
  3. Fluid statics
  4. Variation of pressure with depth

11.4 Variation of pressure with depth in a fluid

<< Chapter < Page
  College physics     Page 1 / 4
Chapter >> Page >
  • Define pressure in terms of weight.
  • Explain the variation of pressure with depth in a fluid.
  • Calculate density given pressure and altitude.

If your ears have ever popped on a plane flight or ached during a deep dive in a swimming pool, you have experienced the effect of depth on pressure in a fluid. At the Earth’s surface, the air pressure exerted on you is a result of the weight of air above you. This pressure is reduced as you climb up in altitude and the weight of air above you decreases. Under water, the pressure exerted on you increases with increasing depth. In this case, the pressure being exerted upon you is a result of both the weight of water above you and that of the atmosphere above you. You may notice an air pressure change on an elevator ride that transports you many stories, but you need only dive a meter or so below the surface of a pool to feel a pressure increase. The difference is that water is much denser than air, about 775 times as dense.

Consider the container in [link] . Its bottom supports the weight of the fluid in it. Let us calculate the pressure exerted on the bottom by the weight of the fluid. That pressure    is the weight of the fluid mg size 12{ ital "mg"} {} divided by the area A size 12{A} {} supporting it (the area of the bottom of the container):

P = mg A . size 12{P= { { ital "mg"} over {A} } } {}

We can find the mass of the fluid from its volume and density:

m = ρV . size 12{m=ρV} {}

The volume of the fluid V size 12{V} {} is related to the dimensions of the container. It is

V = Ah , size 12{V= ital "Ah"} {}

where A size 12{A} {} is the cross-sectional area and h size 12{h} {} is the depth. Combining the last two equations gives

m = ρ Ah . size 12{m=ρ ital "Ah"} {}

If we enter this into the expression for pressure, we obtain

P = ρ Ah g A . size 12{P= { { left (ρ ital "Ah" right )g} over {A} } } {}

The area cancels, and rearranging the variables yields

P = hρg . size 12{P=hρg} {}

This value is the pressure due to the weight of a fluid . The equation has general validity beyond the special conditions under which it is derived here. Even if the container were not there, the surrounding fluid would still exert this pressure, keeping the fluid static. Thus the equation P = hρg size 12{P=hρg} {} represents the pressure due to the weight of any fluid of average density ρ size 12{ρ} {} at any depth h size 12{h} {} below its surface. For liquids, which are nearly incompressible, this equation holds to great depths. For gases, which are quite compressible, one can apply this equation as long as the density changes are small over the depth considered. [link] illustrates this situation.

A container with fluid filled to a depth h. The fluid’s weight w equal to m times g is shown by an arrow pointing downward. A denotes the area of the fluid at the bottom of the container and as well as on the surface.
The bottom of this container supports the entire weight of the fluid in it. The vertical sides cannot exert an upward force on the fluid (since it cannot withstand a shearing force), and so the bottom must support it all.

Calculating the average pressure and force exerted: what force must a dam withstand?

In [link] , we calculated the mass of water in a large reservoir. We will now consider the pressure and force acting on the dam retaining water. (See [link] .) The dam is 500 m wide, and the water is 80.0 m deep at the dam. (a) What is the average pressure on the dam due to the water? (b) Calculate the force exerted against the dam and compare it with the weight of water in the dam (previously found to be 1.96 × 10 13 N ).

Strategy for (a)

The average pressure P ¯ due to the weight of the water is the pressure at the average depth h ¯ of 40.0 m, since pressure increases linearly with depth.

Solution for (a)

The average pressure due to the weight of a fluid is

P ¯ = h ¯ ρg . size 12{P=hρg} {}

Entering the density of water from [link] and taking h ¯ size 12{h} {} to be the average depth of 40.0 m, we obtain

P ¯ = ( 40.0 m ) 10 3 kg m 3 9.80 m s 2 = 3.92 × 10 5 N m 2 = 392 kPa.

Strategy for (b)

The force exerted on the dam by the water is the average pressure times the area of contact:

F = P ¯ A . size 12{F= {overline {P}} A} {}

Solution for (b)

We have already found the value for P ¯ size 12{ { bar {P}}} {} . The area of the dam is A = 80.0 m × 500 m = 4.00 × 10 4 m 2 size 12{A="80" "." 0`m times "500"`m=4 "." "00" times "10" rSup { size 8{4} } `m rSup { size 8{2} } } {} , so that

F = ( 3.92 × 10 5 N/m 2 ) ( 4.00 × 10 4 m 2 ) = 1.57 × 10 10 N. alignl { stack { size 12{F= \( 3 "." "92" times "10" rSup { size 8{5} } `"N/m" rSup { size 8{2} } \) \( 4 "." "00" times "10" rSup { size 8{4} } `m rSup { size 8{2} } \) } {} #" "=1 "." "57" times "10" rSup { size 8{"10"} } `N "." {} } } {}

Discussion

Although this force seems large, it is small compared with the 1.96 × 10 13 N size 12{1 "." "96" times "10" rSup { size 8{"13"} } `N} {} weight of the water in the reservoir—in fact, it is only 0.0800% of the weight. Note that the pressure found in part (a) is completely independent of the width and length of the lake—it depends only on its average depth at the dam. Thus the force depends only on the water’s average depth and the dimensions of the dam, not on the horizontal extent of the reservoir. In the diagram, the thickness of the dam increases with depth to balance the increasing force due to the increasing pressure.epth to balance the increasing force due to the increasing pressure.

Got questions? Get instant answers now!

Questions & Answers

how does Neisseria cause meningitis
Nyibol Reply
what is microbiologist
Muhammad Reply
what is errata
Muhammad
is the branch of biology that deals with the study of microorganisms.
Ntefuni Reply
What is microbiology
Mercy Reply
studies of microbes
Louisiaste
when we takee the specimen which lumbar,spin,
Ziyad Reply
How bacteria create energy to survive?
Muhamad Reply
Bacteria doesn't produce energy they are dependent upon their substrate in case of lack of nutrients they are able to make spores which helps them to sustain in harsh environments
_Adnan
But not all bacteria make spores, l mean Eukaryotic cells have Mitochondria which acts as powerhouse for them, since bacteria don't have it, what is the substitution for it?
Muhamad
they make spores
Louisiaste
what is sporadic nd endemic, epidemic
Aminu Reply
the significance of food webs for disease transmission
Abreham
food webs brings about an infection as an individual depends on number of diseased foods or carriers dully.
Mark
explain assimilatory nitrate reduction
Esinniobiwa Reply
Assimilatory nitrate reduction is a process that occurs in some microorganisms, such as bacteria and archaea, in which nitrate (NO3-) is reduced to nitrite (NO2-), and then further reduced to ammonia (NH3).
Elkana
This process is called assimilatory nitrate reduction because the nitrogen that is produced is incorporated in the cells of microorganisms where it can be used in the synthesis of amino acids and other nitrogen products
Elkana
Examples of thermophilic organisms
Shu Reply
Give Examples of thermophilic organisms
Shu
advantages of normal Flora to the host
Micheal Reply
Prevent foreign microbes to the host
Abubakar
they provide healthier benefits to their hosts
ayesha
They are friends to host only when Host immune system is strong and become enemies when the host immune system is weakened . very bad relationship!
Mark
what is cell
faisal Reply
cell is the smallest unit of life
Fauziya
cell is the smallest unit of life
Akanni
ok
Innocent
cell is the structural and functional unit of life
Hasan
is the fundamental units of Life
Musa
what are emergency diseases
Micheal Reply
There are nothing like emergency disease but there are some common medical emergency which can occur simultaneously like Bleeding,heart attack,Breathing difficulties,severe pain heart stock.Hope you will get my point .Have a nice day ❣️
_Adnan
define infection ,prevention and control
Innocent
I think infection prevention and control is the avoidance of all things we do that gives out break of infections and promotion of health practices that promote life
Lubega
Heyy Lubega hussein where are u from?
_Adnan
en français
Adama
which site have a normal flora
ESTHER Reply
Many sites of the body have it Skin Nasal cavity Oral cavity Gastro intestinal tract
Safaa
skin
Asiina
skin,Oral,Nasal,GIt
Sadik
How can Commensal can Bacteria change into pathogen?
Sadik
How can Commensal Bacteria change into pathogen?
Sadik
all
Tesfaye
by fussion
Asiina
what are the advantages of normal Flora to the host
Micheal
what are the ways of control and prevention of nosocomial infection in the hospital
Micheal
what is inflammation
Shelly Reply
part of a tissue or an organ being wounded or bruised.
Wilfred
what term is used to name and classify microorganisms?
Micheal Reply
Binomial nomenclature
adeolu
Got questions? Join the online conversation and get instant answers!
Jobilize.com Reply
<< Chapter < Page Page > Chapter >>
Practice Key Terms 1

Read also:

Get Jobilize Job Search Mobile App in your pocket Now!

Get it on Google Play Download on the App Store Now




Source:  OpenStax, College physics. OpenStax CNX. Jul 27, 2015 Download for free at http://legacy.cnx.org/content/col11406/1.9
Google Play and the Google Play logo are trademarks of Google Inc.

Notification Switch

Would you like to follow the 'College physics' conversation and receive update notifications?

Ask