Baseband communication is the simplest form of analog communication.
We use analog communication techniques for analog message
signals, like music, speech, and television. Transmission andreception of analog signals using analog results in an
inherently noisy received signal (assuming the channel addsnoise, which it almost certainly does).
The simplest form of analog communication is
baseband
communication .
We use analog communication
techniques for analog message signals, like music, speech, andtelevision. Transmission and reception of analog signals using
analog results in an inherently noisy received signal(assuming the channel adds noise, which it almost certainly
does).
Here, the transmitted signal equals the message times a
transmitter gain.
An example, which is somewhat out of date, is the wireline
telephone system. You don't use baseband communication inwireless systems simply because low-frequency signals do not
radiate well. The receiver in a baseband system can't do muchmore than filter the received signal to remove out-of-band noise
(interference is small in wireline channels). Assuming thesignal occupies a bandwidth of
Hz (the signal's spectrum extends from zero to
), the receiver applies a lowpass
filter having the same bandwidth, as shown in
[link] .
The receiver for baseband communication systems is quite
simple: a lowpass filter having the same bandwidth as thesignal.
We use the
signal-to-noise ratio of the
receiver's output
to evaluate any analog-message communication system. Assume that
the channel introduces an attenuation
and white noise of
spectral height
. The filter does not affect the signal component—we
assume its gain is unity—but does filter the noise,removing frequency components above
Hz. In the filter's output, the
received signal power equals
and the noise power
,
which gives a signal-to-noise ratio of
The signal power
will be
proportional to the bandwidth
;
thus, in baseband communication the signal-to-noise ratio variesonly with transmitter gain and channel attenuation and noise
level.
Questions & Answers
Three charges q_{1}=+3\mu C, q_{2}=+6\mu C and q_{3}=+8\mu C are located at (2,0)m (0,0)m and (0,3) coordinates respectively. Find the magnitude and direction acted upon q_{2} by the two other charges.Draw the correct graphical illustration of the problem above showing the direction of all forces.
To solve this problem, we need to first find the net force acting on charge q_{2}. The magnitude of the force exerted by q_{1} on q_{2} is given by F=\frac{kq_{1}q_{2}}{r^{2}} where k is the Coulomb constant, q_{1} and q_{2} are the charges of the particles, and r is the distance between them.
Muhammed
What is the direction and net electric force on q_{1}= 5µC located at (0,4)r due to charges q_{2}=7mu located at (0,0)m and q_{3}=3\mu C located at (4,0)m?
Capacitor is a separation of opposite charges using an insulator of very small dimension between them. Capacitor is used for allowing an AC (alternating current) to pass while a DC (direct current) is blocked.
Gautam
A motor travelling at 72km/m on sighting a stop sign applying the breaks such that under constant deaccelerate in the meters of 50 metres what is the magnitude of the accelerate
velocity can be 72 km/h in question. 72 km/h=20 m/s, v^2=2.a.x , 20^2=2.a.50, a=4 m/s^2.
Mehmet
A boat travels due east at a speed of 40meter per seconds across a river flowing due south at 30meter per seconds. what is the resultant speed of the boat
which has a higher temperature, 1cup of boiling water or 1teapot of boiling water which can transfer more heat 1cup of boiling water or 1 teapot of boiling water explain your . answer
I believe temperature being an intensive property does not change for any amount of boiling water whereas heat being an extensive property changes with amount/size of the system.
Someone
Scratch that
Someone
temperature for any amount of water to boil at ntp is 100⁰C (it is a state function and and intensive property) and it depends both will give same amount of heat because the surface available for heat transfer is greater in case of the kettle as well as the heat stored in it but if you talk.....
Someone
about the amount of heat stored in the system then in that case since the mass of water in the kettle is greater so more energy is required to raise the temperature b/c more molecules of water are present in the kettle
pratica A on solution of hydro chloric acid,B is a solution containing 0.5000 mole ofsodium chlorid per dm³,put A in the burret and titrate 20.00 or 25.00cm³ portion of B using melting orange as the indicator. record the deside of your burret tabulate the burret reading and calculate the average volume of acid used?
No. According to Isac Newtons law. this two bodies maybe you and the wall beside you.
Attracting depends on the mass och each body and distance between them.
Dlovan
Are you really asking if two bodies have to be charged to be influenced by Coulombs Law?
Specific heat capacity is a measure of the amount of energy required to raise the temperature of a substance by one degree Celsius (or Kelvin). It is measured in Joules per kilogram per degree Celsius (J/kg°C).
AI-Robot
specific heat capacity is the amount of energy needed to raise the temperature of a substance by one degree Celsius or kelvin
ROKEEB
Got questions? Join the online conversation and get instant answers!
