<< Chapter < Page Chapter >> Page >

Water only moves in response to ΔΨ, not in response to the individual components. However, because the individual components influence the total Ψ system , by manipulating the individual components (especially Ψ s ), a plant can control water movement.

Solute potential

Solute potential (Ψ s ), also called osmotic potential, is negative in a plant cell and zero in distilled water. Typical values for cell cytoplasm are –0.5 to –1.0 MPa. Solutes reduce water potential (resulting in a negative Ψ w ) by consuming some of the potential energy available in the water. Solute molecules can dissolve in water because water molecules can bind to them via hydrogen bonds; a hydrophobic molecule like oil, which cannot bind to water, cannot go into solution. The energy in the hydrogen bonds between solute molecules and water is no longer available to do work in the system because it is tied up in the bond. In other words, the amount of available potential energy is reduced when solutes are added to an aqueous system. Thus, Ψ s decreases with increasing solute concentration. Because Ψ s is one of the four components of Ψ system or Ψ total , a decrease in Ψ s will cause a decrease in Ψ total . The internal water potential of a plant cell is more negative than pure water because of the cytoplasm’s high solute content ( [link] ). Because of this difference in water potential water will move from the soil into a plant’s root cells via the process of osmosis. This is why solute potential is sometimes called osmotic potential.

Plant cells can metabolically manipulate Ψ s (and by extension, Ψ total ) by adding or removing solute molecules. Therefore, plants have control over Ψ total via their ability to exert metabolic control over Ψ s .

 Illustration shows a U-shaped tube holding pure water. A semipermeable membrane, which allows water but not solutes to pass, separates the two sides of the tube. The water level on each side of the tube is the same. Beneath this tube are three more tubes, also divided by semipermeable membranes. In the first tube, solute has been added to the right side. Adding solute to the right side lowers psi-s, causing water to move to the right side of the tube. As a result, the water level is higher on the right side. The second tube has pure water on both sides of the membrane. Positive pressure is applied to the left side. Applying positive pressure to the left side causes psi-p to increase. As a results, water moves to the right so that the water level is higher on the right than on the left. The third tube also has pure water, but this time negative pressure is applied to the left side. Applying negative pressure lowers psi-p, causing water to move to the left side of the tube. As a result, the water level is higher on the left.
In this example with a semipermeable membrane between two aqueous systems, water will move from a region of higher to lower water potential until equilibrium is reached. Solutes (Ψ s ), pressure (Ψ p ), and gravity (Ψ g ) influence total water potential for each side of the tube (Ψ total right or left ), and therefore, the difference between Ψ total on each side (ΔΨ). (Ψ m , the potential due to interaction of water with solid substrates, is ignored in this example because glass is not especially hydrophilic). Water moves in response to the difference in water potential between two systems (the left and right sides of the tube).

Positive water potential is placed on the left side of the tube by increasing Ψ p such that the water level rises on the right side. Could you equalize the water level on each side of the tube by adding solute, and if so, how?

Pressure potential

Pressure potential (Ψ p ), also called turgor potential, may be positive or negative ( [link] ). Because pressure is an expression of energy, the higher the pressure, the more potential energy in a system, and vice versa. Therefore, a positive Ψp (compression) increases Ψ total , and a negative Ψ p (tension) decreases Ψ total . Positive pressure inside cells is contained by the cell wall, producing turgor pressure. Pressure potentials are typically around 0.6–0.8 MPa, but can reach as high as 1.5 MPa in a well-watered plant. A Ψ p of 1.5 MPa equates to 210 pounds per square inch (1.5 MPa x 140 lb in -2 MPa -1 = 210 lb/in -2 ). As a comparison, most automobile tires are kept at a pressure of 30–34 psi. An example of the effect of turgor pressure is the wilting of leaves and their restoration after the plant has been watered ( [link] ). Water is lost from the leaves via transpiration (approaching Ψ p = 0 MPa at the wilting point) and restored by uptake via the roots.

Get Jobilize Job Search Mobile App in your pocket Now!

Get it on Google Play Download on the App Store Now




Source:  OpenStax, Bmcc 102 - concepts of biology. OpenStax CNX. Aug 11, 2015 Download for free at https://legacy.cnx.org/content/col11856/1.3
Google Play and the Google Play logo are trademarks of Google Inc.

Notification Switch

Would you like to follow the 'Bmcc 102 - concepts of biology' conversation and receive update notifications?

Ask