<< Chapter < Page Chapter >> Page >
Setting the Sine Wave to 300 Hz

Make a note of the accuracy of the model.

Changing the frame sizes

Increase the Samples per frame to 1024 in both the “Sine Wave” and the “Random Source” Blocks.

Adjusting Frame Size for Sine Wave
Adjusting the Frame Size for the Random Source

Run the model again.

Question: How does this change to the frame size affect performance?

Setting the delay value

Click on the “Delay” Block. Change the number of Delay (samples) to 50.

Setting the Delay (samples)

Run the model again and make a note of the accuracy of the measurement.

Change Delay (samples) The Delay (samples) should be smaller than the frame size, otherwise the frames do not overlap. to 12 and run the model again.

Question: How does the value of delay (samples) affect the accuracy of the model?

Changing the amount of noise present

Reload the original model to restore the initial settings.

Change the amount of Gain to make the gain 0.10 (10% noise).

Changing the Amount of Noise Present

Run the model and make a note of the accuracy of the measurements. Repeat, but this time, use a gain of 0.01 (1% noise).

Question: Does the algorithm work better for high signal-to-noise ratios or for low signal-to-noise ratios? Make a note of the answer.

Changing the sampling frequency

Change the sample time in both the “Sine Wave” and the “Random Noise” blocks to 48000 Hz.

Changing the Sine Wave Sample Time
Changing the Random Source Sample Time

Run the model.

Question: Does the model produce better results with 8000Hz sampling or 48000 Hz sampling? Make a note of the answer.

The fully optimized simulation

You should now know what are the optimum parameters for the simulation.

Set these parameters and run the model.

Summary of simulation

You have now run the signal-to-noise ratio model and should be aware of the best settings for consistency of measurements, delay and sampling frequency.

You are now ready to go to the C6713 DSK Model.

Real-time model for ti c6713 dsk

Texas instruments c6713 dsk setup

Texas Instruments C6713 DSK Setup

Alternatively, you can use computer loudspeakers.

Starting code composer studio

There are several stages required in order to implement the Signal-to-Noise measurement. These are now described.

Starting up code composer studio

Start Code Composer Studio for C6713 DSK and use Debug ->Connect

Startup Screen for Code Composer Studio (CCS)

The texas instruments c6713 dsk model

You will now use the knowledge you have gained during the PC Simulation to produce an optimized version of this algorithm for use with the Texas Instruments C6713 DSK.

Opening the c6713 dsk model

Open the SignalToNoiseDSK6713.mdl.

The parent is shown in Figure 15.

SignalToNoiseDSK6713.mdl

Double click on the “function()” block.

Viewing the signal-to-noise measurement algorithm

The details of the C6713 Algorithm are shown in Figure 16.

Audio Noise Gate

Setting the sampling rate and frame size

Double-click on the “Mic In C6713 DSK ADC” block.

Set the Sampling rate (Hz) and Samples per frame fields to the best value you found while carrying out the Simulation. The values may be different to those written here.

Setting the Sampling Rate and Frame Size

Setting the delay size

Double-click on the “Delay” block. Set the Delay (samples) to the best value found during simulation. The value will not be 999!

Setting the Delay Size

Returning to the parent system

From the Toolbar, select the “Up Arrow” icon. This returns you to the next higher level.

Returning to the Parent System

Building the model

Selecting real-time workshop

Select Tools ->Real-Time Workshop ->Build Model.

Building the Model

The completed model running on code composer studio

From the folders on the left, select the source code for the project.

The Completed Model Running in Code Composer Studio

Different settings on the c6713 dsk

Microphone straight through to loudspeakers

To check out the microphone and loudspeakers, set the DIP switches on the C6713 DSK as follows:

Switch Position 0

The microphone is fed directly to the loudspeakers. There is no noise gate.

Switch position for the audio noise gate

To run the Audio Noise Gate, set the DIP switch to 1.

Switch Position 1 for Audio Noise Gate

Note that when you are not speaking, there is no audio output at all – just silence.

Modifying the model

The next stage is to modify the model. You can change the smoothing filter. If the filter is too long, the delay will be noticeable.

Changing the filter type

Double-click on the “Lowpass” block. Change the Order to a value other than 10.

Changing the Number of Filter Elements

Re-building the model

Select Tools ->Real-Time Workshop ->Build Model.

Re-building the Model

Running the updated model

Run the updated model and listen to the effect on the audio noise gate.

Some things to try

You may wish to experiment with different settings. Here are some suggestions.

Add an input filter

While running the Simulation, you will have noticed that the Signal-to-Noise Algorithm works better on some frequencies than others.

Add the appropriate filter to select only the frequencies where the algorithm works well.

Process stereo inputs

Change the input from “Microphone” to “Stereo Line Input”.

Add a second channel to make the processing stereo.

Best signal selection

When stage 3.2 has been completed, modify the model so that the output is the better of the two stereo inputs.

MATLAB and Simulink are registered trademarks of The MathWorks, Inc. See www.mathworks.com/trademarks for a list of additional trademarks. Other product or brand names may be trademarks or registered trademarks of their respective holders.

Questions & Answers

the diagram of the digestive system
Assiatu Reply
allimentary cannel
Ogenrwot
How does twins formed
William Reply
They formed in two ways first when one sperm and one egg are splited by mitosis or two sperm and two eggs join together
Oluwatobi
what is genetics
Josephine Reply
Genetics is the study of heredity
Misack
how does twins formed?
Misack
What is manual
Hassan Reply
discuss biological phenomenon and provide pieces of evidence to show that it was responsible for the formation of eukaryotic organelles
Joseph Reply
what is biology
Yousuf Reply
the study of living organisms and their interactions with one another and their environments
AI-Robot
the study of living organisms and their interactions with one another and their environment.
Wine
discuss the biological phenomenon and provide pieces of evidence to show that it was responsible for the formation of eukaryotic organelles in an essay form
Joseph Reply
what is the blood cells
Shaker Reply
list any five characteristics of the blood cells
Shaker
lack electricity and its more savely than electronic microscope because its naturally by using of light
Abdullahi Reply
advantage of electronic microscope is easily and clearly while disadvantage is dangerous because its electronic. advantage of light microscope is savely and naturally by sun while disadvantage is not easily,means its not sharp and not clear
Abdullahi
cell theory state that every organisms composed of one or more cell,cell is the basic unit of life
Abdullahi
is like gone fail us
DENG
cells is the basic structure and functions of all living things
Ramadan
What is classification
ISCONT Reply
is organisms that are similar into groups called tara
Yamosa
in what situation (s) would be the use of a scanning electron microscope be ideal and why?
Kenna Reply
A scanning electron microscope (SEM) is ideal for situations requiring high-resolution imaging of surfaces. It is commonly used in materials science, biology, and geology to examine the topography and composition of samples at a nanoscale level. SEM is particularly useful for studying fine details,
Hilary
cell is the building block of life.
Condoleezza Reply
what is cell divisoin?
Aron Reply
Diversity of living thing
ISCONT
what is cell division
Aron Reply
Cell division is the process by which a single cell divides into two or more daughter cells. It is a fundamental process in all living organisms and is essential for growth, development, and reproduction. Cell division can occur through either mitosis or meiosis.
AI-Robot
What is life?
Allison Reply
life is defined as any system capable of performing functions such as eating, metabolizing,excreting,breathing,moving,Growing,reproducing,and responding to external stimuli.
Mohamed
Got questions? Join the online conversation and get instant answers!
Jobilize.com Reply

Get Jobilize Job Search Mobile App in your pocket Now!

Get it on Google Play Download on the App Store Now




Source:  OpenStax, From matlab and simulink to real-time with ti dsp's. OpenStax CNX. Jun 08, 2009 Download for free at http://cnx.org/content/col10713/1.1
Google Play and the Google Play logo are trademarks of Google Inc.

Notification Switch

Would you like to follow the 'From matlab and simulink to real-time with ti dsp's' conversation and receive update notifications?

Ask