<< Chapter < Page Chapter >> Page >
This module shows the implementation of a DTMF detector using the DSK6713. The detector is desgined using Simulink.

Introduction

The Dual-tone multi-frequency (DTMF) signaling method was developed originally to replace pulse (Dial Pulse or DP in the U.S. ) and loop disconnect (LD) signaling methods to dial numbers, in order to shorten the holding time of the switch during dialing , specially for long distance calls.

DTMF signaling uses two tones to represent each key on the touch pad. There are 12 distinct tones The DTMF method defines four additional digits: “A”, “B”,”C”&“D”. Most of the systems today do not use those digits. (Please refer to Table 1). When any key is pressed the tone of the column and the tone of the row are generated. As an example, pressing the '5' button generates the tones 770 Hz and 1336 Hz. The frequencies were chosen to avoid harmonics: no frequency is a multiple of another, the difference between any two frequencies does not equal any of the frequencies, and the sum of any two frequencies does not equal any of the frequencies.

DTMF Frequencies
. 1209 Hz 1336 Hz 1477 Hz
697 Hz 1 2 3
770 Hz 4 5 6
852 Hz 7 8 9
941 Hz * 0 #

Table 1- DTMF frequencies

The low frequencies are referred as rows, The higher frequencies are referred as columns.

This example will show the implementation of a DTMF receiver using the DSK6713. The DTMF receiver will be based on the simulation model used in the Simulink demo. A graphic user interface (GUI) will also be created to activate the DSK6713. DTMF digits will be sent from the PC sound card.

Simulation

The simulation model

Figure 1 shows the model used to simulate DTMF detection and generation.

DTMF Simulation

The DTMF generator is composed by 7 sine wave generators, corresponding to the 7 DTMF frequencies. The oscillators are grouped as described in Table 1. The oscillators’’ outputs are multiplexed and summed (Please refer to Figure 2). Upon selection of a digit to be transmitted, the correspondent oscillators are activated.

DTMF Generation

The DTMF detection comprises two processes, the frequency detection algorithm itself, and a leading edge detection subsystem.

The frequency detection subsystem measures the energy present at the seven frequencies, and calculates the digit by taking the component of maximum energy in the lower and upper frequency groups. The process is shown in Figure 3. This process runs continuously; however the calculated digit is reported only if its energy is above a threshold as determined by the leading edge detection subsystem. The DTMF detection process is shown in Figure 4.

Frequency Detection
DTMF Detection

Running the simulation

  • Open the simulation model “DTMF.mdl”
  • In order to select the digit double click the DTMF generator subsystem and enter the digits to be sent as follows:
"Dialing" DTMF Digits
  • Activate the simulation, the detected digits will be displayed as shown:

Questions & Answers

what is mutation
Janga Reply
what is a cell
Sifune Reply
how is urine form
Sifune
what is antagonism?
mahase Reply
classification of plants, gymnosperm features.
Linsy Reply
what is the features of gymnosperm
Linsy
how many types of solid did we have
Samuel Reply
what is an ionic bond
Samuel
What is Atoms
Daprince Reply
what is fallopian tube
Merolyn
what is bladder
Merolyn
what's bulbourethral gland
Eduek Reply
urine is formed in the nephron of the renal medulla in the kidney. It starts from filtration, then selective reabsorption and finally secretion
onuoha Reply
State the evolution relation and relevance between endoplasmic reticulum and cytoskeleton as it relates to cell.
Jeremiah
what is heart
Konadu Reply
how is urine formed in human
Konadu
how is urine formed in human
Rahma
what is the diference between a cavity and a canal
Pelagie Reply
what is the causative agent of malaria
Diamond
malaria is caused by an insect called mosquito.
Naomi
Malaria is cause by female anopheles mosquito
Isaac
Malaria is caused by plasmodium Female anopheles mosquitoe is d carrier
Olalekan
a canal is more needed in a root but a cavity is a bad effect
Commander
what are pathogens
Don Reply
In biology, a pathogen (Greek: πάθος pathos "suffering", "passion" and -γενής -genēs "producer of") in the oldest and broadest sense, is anything that can produce disease. A pathogen may also be referred to as an infectious agent, or simply a germ. The term pathogen came into use in the 1880s.[1][2
Zainab
A virus
Commander
Definition of respiration
Muhsin Reply
respiration is the process in which we breath in oxygen and breath out carbon dioxide
Achor
how are lungs work
Commander
where does digestion begins
Achiri Reply
in the mouth
EZEKIEL
what are the functions of follicle stimulating harmones?
Rashima Reply
stimulates the follicle to release the mature ovum into the oviduct
Davonte
what are the functions of Endocrine and pituitary gland
Chinaza
endocrine secrete hormone and regulate body process
Achor
while pituitary gland is an example of endocrine system and it's found in the Brain
Achor
what's biology?
Egbodo Reply
Biology is the study of living organisms, divided into many specialized field that cover their morphology, physiology,anatomy, behaviour,origin and distribution.
Lisah
biology is the study of life.
Alfreda
Biology is the study of how living organisms live and survive in a specific environment
Sifune
Got questions? Join the online conversation and get instant answers!
Jobilize.com Reply

Get Jobilize Job Search Mobile App in your pocket Now!

Get it on Google Play Download on the App Store Now




Source:  OpenStax, From matlab and simulink to real-time with ti dsp's. OpenStax CNX. Jun 08, 2009 Download for free at http://cnx.org/content/col10713/1.1
Google Play and the Google Play logo are trademarks of Google Inc.

Notification Switch

Would you like to follow the 'From matlab and simulink to real-time with ti dsp's' conversation and receive update notifications?

Ask