<< Chapter < Page Chapter >> Page >

As is common for many 1960’s and 70’s Lotus cars, the front brake calipers are Girling 14LF. These were widely used over this period by domestic manufacturers such as Ford and Triumph. A schematic of the caliper and brake assembly is shown in [link] .

Schematic representation of the Girling sourced front brakes.

Disassembly and cleaning

The brake pads are removed by releasing the clips from the retaining pins. The pins are then slid out of the caliper assembly, at which point the pads are removed out the back of each assembly. Using a screwdriver, the old piston boots are removed along with their retaining clips ( [link] ).

Used piston boot and retaining clip.

The pistons can then be removed by connecting the brake caliper to a compressed air source. Placing the caliper assembly into a bench vice and putting an old glove or towel between the pistons, the air is introduced into the caliper. Unless the piston is rusted in place, one or both should be released from their respective barrels.

Under no circumstances should fingers or any body part be placed in the caliper while removing the pistons with compressed air. Correct safety glasses and gloves should be work while attempting to remove the pistons.

Unfortunately, in many cases only one of the pistons is removed. If this occurs, the two halves of the caliper assembly must be separated. It is important not to loose the rubber O-ring that is positioned between the caliper halves, since this is not included in most rebuild kits. The half with the piston in is then subjected to air pressure, while the hole that connects the two halves (for brake fluid passage) is covered by a glove or similar. In the present case this resulted in the piston being only partially removed from the caliper assembly, and additional force was applied using vice grips. Due to difficulties in removing the pistons from the caliper assembly, the outer face (barrel) of the pistons was damaged ( [link] ). Given that a seal between piston and the caliper assembly is required, it was decided that it would be easier to replace the pistons.

The piston should be pointed away from persons or breakable items since under pressure it can be expelled with violent force. Placing a blanket over the assembly is advised. Correct safety glasses and gloves should be work while attempting to remove the pistons.
One of the new pistons (A) and an original piston (B).

Finally, the rubber seals inside the caliper barrels are removed using a sharp point or a small screwdriver. The two halves of the caliper assembly ( [link] ) are ready for cleaning. The caliper bodies were Teflon ® coated by PolyDyne Performance Coatings. The coating was chosen to allow for the ease of cleaning and removal of brake dust that ordinarily builds up on any suspension components.

The caliper assemblies after removal of the pistons and all seals.

Assembly

The calipers were rebuilt using a TRW rebuild (SP2697) kit from Moss Motors. The rebuild kit consists of 4 piston boots, 4 rubber seals, 4 retaining clips, and 2 rubber dust caps ( [link] and [link] ). One part that does not come in the kit and therefore has to be reused is the rubber washer that seals between the two halves of the caliper. This must be retained from the original; however, all other seals are disposable.

Contents of the caliper rebuild kit.
One each of the piston seal (A), piston boot (B), and retaining clip (C).

The first task is to install the rubber seal ( [link] A) inside the caliper. The ring is fed into the groove inside the barrel of the caliper, taking care not to damage or twist it ( [link] ). One piston is then installed into each of the caliper halves. It is important to push the piston in straight. In order to ease the piston in, the rubber seal and caliper barrel are greased. A small amount of silicone vacuum grease is suitable, although if none is available, a light rub with break fluid will also work. Once the pistons are fully pressed into the caliper, the piston boot ( [link] B) is stretched over the piston and fitted to the caliper with the retaining clips ( [link] C). The final result is shown in [link] .

View of the inside of one half of the caliper showing the location of the piston seal (arrowed).
One half of a caliper showing the installed piston, with its boot and retaining clip.

Before the two caliper halves are joined, it is important not to forget the rubber washer that seals the fluid passage between the two halves of the caliper ( [link] ). With this in place the two halves are bolted together ( [link] ).

The small rubber washer (not supplied in the rebuild kit) that seals the two halves of the caliper.
View of one of the finished calipers, showing the four bolts that hold the two halves together.

Since brake pads will not be installed until the calipers are fitted to the upright/hub/disk combination, the pad retaining pins and clips are fitted to ensure they do not get lost ( [link] ). A view of the finished calipers is shown in [link] , including the rubber dust caps in place over the bleed screws.

One of the finished calipers showing the brake pad pins and retaining clips.
Both calipers reassembled.

Resources

  • PolyDyne Performance Coatings, 11211 Neeshaw Drive, Houston, Texas 77065, USA. Tel: +1 888 765 9396 or +1 281 894 6382. www.polydyn.com .
  • Moss Motors, Ltd. 440 Rutherford Street, Goleta, CA 93117, USA. Tel: +1 800 667 7872 or +1 805 681 3400. www.mossmotors.com .

Questions & Answers

do you think it's worthwhile in the long term to study the effects and possibilities of nanotechnology on viral treatment?
Damian Reply
absolutely yes
Daniel
how to know photocatalytic properties of tio2 nanoparticles...what to do now
Akash Reply
it is a goid question and i want to know the answer as well
Maciej
characteristics of micro business
Abigail
Do somebody tell me a best nano engineering book for beginners?
s. Reply
what is fullerene does it is used to make bukky balls
Devang Reply
are you nano engineer ?
s.
fullerene is a bucky ball aka Carbon 60 molecule. It was name by the architect Fuller. He design the geodesic dome. it resembles a soccer ball.
Tarell
what is the actual application of fullerenes nowadays?
Damian
That is a great question Damian. best way to answer that question is to Google it. there are hundreds of applications for buck minister fullerenes, from medical to aerospace. you can also find plenty of research papers that will give you great detail on the potential applications of fullerenes.
Tarell
what is the Synthesis, properties,and applications of carbon nano chemistry
Abhijith Reply
Mostly, they use nano carbon for electronics and for materials to be strengthened.
Virgil
is Bucky paper clear?
CYNTHIA
so some one know about replacing silicon atom with phosphorous in semiconductors device?
s. Reply
Yeah, it is a pain to say the least. You basically have to heat the substarte up to around 1000 degrees celcius then pass phosphene gas over top of it, which is explosive and toxic by the way, under very low pressure.
Harper
Do you know which machine is used to that process?
s.
how to fabricate graphene ink ?
SUYASH Reply
for screen printed electrodes ?
SUYASH
What is lattice structure?
s. Reply
of graphene you mean?
Ebrahim
or in general
Ebrahim
in general
s.
Graphene has a hexagonal structure
tahir
On having this app for quite a bit time, Haven't realised there's a chat room in it.
Cied
what is biological synthesis of nanoparticles
Sanket Reply
what's the easiest and fastest way to the synthesize AgNP?
Damian Reply
China
Cied
types of nano material
abeetha Reply
I start with an easy one. carbon nanotubes woven into a long filament like a string
Porter
many many of nanotubes
Porter
what is the k.e before it land
Yasmin
what is the function of carbon nanotubes?
Cesar
I'm interested in nanotube
Uday
what is nanomaterials​ and their applications of sensors.
Ramkumar Reply
what is nano technology
Sravani Reply
what is system testing?
AMJAD
preparation of nanomaterial
Victor Reply
Yes, Nanotechnology has a very fast field of applications and their is always something new to do with it...
Himanshu Reply
good afternoon madam
AMJAD
what is system testing
AMJAD
what is the application of nanotechnology?
Stotaw
In this morden time nanotechnology used in many field . 1-Electronics-manufacturad IC ,RAM,MRAM,solar panel etc 2-Helth and Medical-Nanomedicine,Drug Dilivery for cancer treatment etc 3- Atomobile -MEMS, Coating on car etc. and may other field for details you can check at Google
Azam
anybody can imagine what will be happen after 100 years from now in nano tech world
Prasenjit
after 100 year this will be not nanotechnology maybe this technology name will be change . maybe aftet 100 year . we work on electron lable practically about its properties and behaviour by the different instruments
Azam
name doesn't matter , whatever it will be change... I'm taking about effect on circumstances of the microscopic world
Prasenjit
how hard could it be to apply nanotechnology against viral infections such HIV or Ebola?
Damian
silver nanoparticles could handle the job?
Damian
not now but maybe in future only AgNP maybe any other nanomaterials
Azam
Hello
Uday
I'm interested in Nanotube
Uday
this technology will not going on for the long time , so I'm thinking about femtotechnology 10^-15
Prasenjit
how did you get the value of 2000N.What calculations are needed to arrive at it
Smarajit Reply
Privacy Information Security Software Version 1.1a
Good
Berger describes sociologists as concerned with
Mueller Reply
Got questions? Join the online conversation and get instant answers!
QuizOver.com Reply

Get the best Algebra and trigonometry course in your pocket!





Source:  OpenStax, Lotus seven s4 (type 60): design, restoration, and maintenance. OpenStax CNX. Jun 07, 2013 Download for free at http://cnx.org/content/col11418/1.19
Google Play and the Google Play logo are trademarks of Google Inc.

Notification Switch

Would you like to follow the 'Lotus seven s4 (type 60): design, restoration, and maintenance' conversation and receive update notifications?

Ask