<< Chapter < Page Chapter >> Page >

For this question, consider the circuit shown in the following figure.

Circuit that across the top from left to right goes point b, battery with voltage E1, point c, resistor with resistance r1, and point d; across the middle goes point a, battery with voltage E2, point k, resistor with resistance r2, point l, resistor with resistance R2, and point e; across the bottom goes point j, battery with voltage E3, point i, resistor with resistance r3, and point h; along the left side from top to bottom goes a resistor with resistance R1, point a, and a resistor with resistance R3; and along the right side goes a resistor with resistance R5, point e, a resistor with resistance r4, point f, a battery with voltage E4, and point g. Additionally, there are three arrows showing the direction of the current: one between point a and the resistor with resistance R1 pointing up; another between point a and the battery with voltage E2 pointing right; and another between point j and the resistor with resistance R3 pointing up.
  1. Assuming that none of the three currents ( I 1 , I 2 , and I 3 ) are equal to zero, which of the following statements is false?

    1. I 3 = I 1 + I 2 at point a .
    2. I 2 = I 3 - I 1 at point e .
    3. The current through R 3 is equal to the current through R 5.
    4. The current through R 1 is equal to the current through R 5.
  2. Which of the following statements is true?

    1. E 1 + E 2 + I 1 R 1 - I 2 R 2 + I 1 r 1 - I 2 r 2 + I 1 R 5 = 0
    2. - E 1 + E 2 + I 1 R 1 - I 2 R 2 + I 1 r 1 - I 2 r 2 - I 1 R 5 = 0
    3. E 1 - E 2 - I 1 R 1 + I 2 R 2 - I 1 r 1 + I 2 r 2 - I 1 R 5 = 0
    4. E 1 + E 2 - I 1 R 1 + I 2 R 2 - I 1 r 1 + I 2 r 2 + I 1 R 5 = 0
  3. If I 1 = 5 A and I 3 = -2 A, which of the following statements is false?

    1. The current through R 1 will flow from a to b and will be equal to 5 A.
    2. The current through R 3 will flow from a to j and will be equal to 2 A.
    3. The current through R 5 will flow from d to e and will be equal to 5 A.
    4. None of the above.
  4. If I 1 = 5 A and I 3 = -2 A, I 2 will be equal to

    1. 3 A
    2. -3 A
    3. 7 A
    4. -7 A

a. (c)

b. (c)

c. (d)

d. (d)

Got questions? Get instant answers now!
A circuit with nothing on the top or bottom, but a battery marked E on the left, a resistor marked R1 in the middle, and a resistor marked R2 on the right.

In an experiment this circuit is set up. Three ammeters are used to record the currents in the three vertical branches (with R 1 , R 2 , and E) . The readings of the ammeters in the resistor branches (i.e. currents in R 1 and R 2 ) are 2 A and 3 A respectively.

  1. Find the equation obtained by applying Kirchhoff’s loop rule in the loop involving R 1 and R 2 .
  2. What will be the reading of the third ammeter (i.e. the branch with E )? If E were replaced by 3 E , how would this reading change?
  3. If the original circuit is modified by adding another voltage source (as shown in the following circuit), find the readings of the three ammeters.
A circuit a battery marked E on the left, a resistor marked R1 in the middle, and a resistor marked R2 on the right. There is nothing on the bottom, and on the top, there is a battery marked 2E between the two resistors.
Got questions? Get instant answers now!
Circuit with a battery with voltage E1 and resistor with resistance r1 across the top from left to right; point A, a resistor with resistance R1, and point B across the middle; and a battery marked E2 and a resistor with resistance r2 across the bottom. Additionally, on the left, from top to bottom there is a resistor with resistance R2 and point A; on the right, from top to bottom there is point B and a resistor with resistance R3.

In this circuit, assume the currents through R 1 , R 2 and R 3 are I 1 , I 2 and I 3 respectively and all are flowing in the clockwise direction.

  1. Find the equation obtained by applying Kirchhoff’s junction rule at point A.
  2. Find the equations obtained by applying Kirchhoff’s loop rule in the upper and lower loops.
  3. Assume R 1 = R 2 = 6 Ω, R 3 = 12 Ω, r 1 = r 2 = 0 Ω, E 1 = 6 V and E 2 = 4 V. Calculate I 1 , I 2 and I 3 .
  4. For the situation in which E 2 is replaced by a closed switch, repeat parts (a) and (b). Using the values for R 1 , R 2 , R 3 , r 1 and E 1 from part (c) calculate the currents through the three resistors.
  5. For the circuit in part (d) calculate the output power of the voltage source and across all the resistors. Examine if energy is conserved in the circuit.
  6. A student implemented the circuit of part (d) in the lab and measured the current though one of the resistors as 0.19 A. According to the results calculated in part (d) identify the resistor(s). Justify any difference in measured and calculated value.
  1. I 1 + I 3 = I 2
  2. E 1 - I 1 R 1 - I 2 R 2 - I 1 r 1 = 0; - E 2 + I 1 R 1 - I 3 R 3 - I 3 r 2 = 0
  3. I 1 = 8/15 A, I 2 = 7/15 A and I 3 = - 1/15 A
  4. I 1 = 2/5 A, I 2 = 3/5 A and I 3 = 1/5 A
  5. P E1 = 18/5 W and P R1 = 24/25 W, P R2 = 54/25 W, P R3 = 12/25 W. Yes, P E1 = P R1 + P R2 + P R3
  6. R 3, losses in the circuit
Got questions? Get instant answers now!

Section summary

  • Kirchhoff’s rules can be used to analyze any circuit, simple or complex.
  • Kirchhoff’s first rule—the junction rule: The sum of all currents entering a junction must equal the sum of all currents leaving the junction.
  • Kirchhoff’s second rule—the loop rule: The algebraic sum of changes in potential around any closed circuit path (loop) must be zero.
  • The two rules are based, respectively, on the laws of conservation of charge and energy.
  • When calculating potential and current using Kirchhoff’s rules, a set of conventions must be followed for determining the correct signs of various terms.
  • The simpler series and parallel rules are special cases of Kirchhoff’s rules.

Conceptual questions

Can all of the currents going into the junction in [link] be positive? Explain.

Got questions? Get instant answers now!
The diagram shows a T junction with currents I sub one, I sub two, and I sub three entering the T junction.

Apply the junction rule to junction b in [link] . Is any new information gained by applying the junction rule at e? (In the figure, each emf is represented by script E.)

Got questions? Get instant answers now!
The diagram shows a complex circuit with four voltage sources: E sub one, E sub two, E sub three, E sub four and several resistive loads, wired in two loops and two junctions. Several points on the diagram are marked with letters a through g. The current in each branch is labeled separately.

(a) What is the potential difference going from point a to point b in [link] ? (b) What is the potential difference going from c to b? (c) From e to g? (d) From e to d?

Got questions? Get instant answers now!

Apply the loop rule to loop afedcba in [link] .

Got questions? Get instant answers now!

Apply the loop rule to loops abgefa and cbgedc in [link] .

Got questions? Get instant answers now!

Problem exercises

Apply the loop rule to loop abcdefgha in [link] .

I 2 R 2 + emf 1 I 2 r 1 + I 3 R 3 + I 3 r 2 - emf 2 = 0 size 12{ {underline {-I rSub { size 8{2} } R rSub { size 8{3} } + "emf" rSub { size 8{1} } - ital " I" rSub { size 8{2} } r rSub { size 8{1} } + ital " I" rSub { size 8{3} } r rSub { size 8{3} } + ital " I" rSub { size 8{3} } r rSub { size 8{2} } +- "emf" rSub { size 8{2} } =" 0"}} } {}

Got questions? Get instant answers now!

Apply the loop rule to loop aedcba in [link] .

Got questions? Get instant answers now!

Verify the second equation in [link] by substituting the values found for the currents I 1 size 12{I rSub { size 8{1} } } {} and I 2 size 12{I rSub { size 8{2} } } {} .

Got questions? Get instant answers now!

Verify the third equation in [link] by substituting the values found for the currents I 1 size 12{I rSub { size 8{1} } } {} and I 3 size 12{I rSub { size 8{3} } } {} .

Got questions? Get instant answers now!

Apply the junction rule at point a in [link] .

The diagram shows a complex circuit with four voltage sources E sub one, E sub two, E sub three, E sub four and several resistive loads, wired in two loops and many junctions. Several points on the diagram are marked with letters a through j. The current in each branch is labeled separately.

I 3 = I 1 + I 2 size 12{I rSub { size 8{3} } = ital " I" rSub { size 8{1} } + ital " I" rSub { size 8{2} } } {}

Got questions? Get instant answers now!

Apply the loop rule to loop abcdefghija in [link] .

Got questions? Get instant answers now!

Apply the loop rule to loop akledcba in [link] .

emf 2 - I 2 r 2 - I 2 R 2 + I 1 R 5 + I 1 r 1 - emf 1 + I 1 R 1 = 0 size 12{ {underline { "emf" rSub { size 8{2} } +- ital " I" rSub { size 8{2} } r rSub { size 8{2} } +- ital " I" rSub { size 8{2} } R rSub { size 8{2} } + ital " I" rSub { size 8{1} } R rSub { size 8{5} } +I rSub { size 8{1} } r rSub { size 8{1} } +- "emf" rSub { size 8{1} } + ital " I" rSub { size 8{1} } R rSub { size 8{1} } = 0}} } {}

Got questions? Get instant answers now!

Find the currents flowing in the circuit in [link] . Explicitly show how you follow the steps in the Problem-Solving Strategies for Series and Parallel Resistors .

Got questions? Get instant answers now!

Solve [link] , but use loop abcdefgha instead of loop akledcba. Explicitly show how you follow the steps in the Problem-Solving Strategies for Series and Parallel Resistors .

(a) I 1 = 4.75 A size 12{I rSub { size 8{1} } =4 cdot "75 A"} {}

(b) I 2 = - 3 . 5 A size 12{I rSub { size 8{"2 "} } = +- 3 "." "5 A"} {} {}

(c) I 3 = 8 . 25 A size 12{I rSub { size 8{3} } =8 "." "25"" A"} {}

Got questions? Get instant answers now!

Find the currents flowing in the circuit in [link] .

Got questions? Get instant answers now!

Unreasonable Results

Consider the circuit in [link] , and suppose that the emfs are unknown and the currents are given to be I 1 = 5 . 00 A , I 2 = 3 .0 A size 12{I rSub { size 8{2} } =3 "." 0" A"} {} , and I 3 = –2 . 00 A size 12{I rSub { size 8{3} } "=-"2 "." "00"" A"} {} . (a) Could you find the emfs? (b) What is wrong with the assumptions?

The diagram shows a complex circuit with two voltage sources E sub one and E sub two, and three resistive loads, wired in two loops and two junctions. Several points on the diagram are marked with letters a through h. The current in each branch is labeled separately.

(a) No, you would get inconsistent equations to solve.

(b) I 1 I 2 + I 3 size 12{I rSub { size 8{1} }<>I rSub { size 8{2} } +I rSub { size 8{3} } } {} . The assumed currents violate the junction rule.

Got questions? Get instant answers now!

Questions & Answers

what is mutation
Janga Reply
what is a cell
Sifune Reply
how is urine form
Sifune
what is antagonism?
mahase Reply
classification of plants, gymnosperm features.
Linsy Reply
what is the features of gymnosperm
Linsy
how many types of solid did we have
Samuel Reply
what is an ionic bond
Samuel
What is Atoms
Daprince Reply
what is fallopian tube
Merolyn
what is bladder
Merolyn
what's bulbourethral gland
Eduek Reply
urine is formed in the nephron of the renal medulla in the kidney. It starts from filtration, then selective reabsorption and finally secretion
onuoha Reply
State the evolution relation and relevance between endoplasmic reticulum and cytoskeleton as it relates to cell.
Jeremiah
what is heart
Konadu Reply
how is urine formed in human
Konadu
how is urine formed in human
Rahma
what is the diference between a cavity and a canal
Pelagie Reply
what is the causative agent of malaria
Diamond
malaria is caused by an insect called mosquito.
Naomi
Malaria is cause by female anopheles mosquito
Isaac
Malaria is caused by plasmodium Female anopheles mosquitoe is d carrier
Olalekan
a canal is more needed in a root but a cavity is a bad effect
Commander
what are pathogens
Don Reply
In biology, a pathogen (Greek: πάθος pathos "suffering", "passion" and -γενής -genēs "producer of") in the oldest and broadest sense, is anything that can produce disease. A pathogen may also be referred to as an infectious agent, or simply a germ. The term pathogen came into use in the 1880s.[1][2
Zainab
A virus
Commander
Definition of respiration
Muhsin Reply
respiration is the process in which we breath in oxygen and breath out carbon dioxide
Achor
how are lungs work
Commander
where does digestion begins
Achiri Reply
in the mouth
EZEKIEL
what are the functions of follicle stimulating harmones?
Rashima Reply
stimulates the follicle to release the mature ovum into the oviduct
Davonte
what are the functions of Endocrine and pituitary gland
Chinaza
endocrine secrete hormone and regulate body process
Achor
while pituitary gland is an example of endocrine system and it's found in the Brain
Achor
what's biology?
Egbodo Reply
Biology is the study of living organisms, divided into many specialized field that cover their morphology, physiology,anatomy, behaviour,origin and distribution.
Lisah
biology is the study of life.
Alfreda
Biology is the study of how living organisms live and survive in a specific environment
Sifune
Got questions? Join the online conversation and get instant answers!
Jobilize.com Reply
Practice Key Terms 4

Get Jobilize Job Search Mobile App in your pocket Now!

Get it on Google Play Download on the App Store Now




Source:  OpenStax, College physics for ap® courses. OpenStax CNX. Nov 04, 2016 Download for free at https://legacy.cnx.org/content/col11844/1.14
Google Play and the Google Play logo are trademarks of Google Inc.

Notification Switch

Would you like to follow the 'College physics for ap® courses' conversation and receive update notifications?

Ask