<< Chapter < Page Chapter >> Page >
This module provides a brief introduction to instrumenting a circuit simulation in National Instruments Multisim. Multisim is fully featured SPICE schematic capture and simulation tool used for circuit design, simulation, and in combination with Ultiboard for layout of custom PCBs.

Instrumenting a simulation in multisim

Virtual instruments are components in Multisim which model real-world bench-top instruments. Examples of virtualinstruments in Multisim include Oscilloscopes, Function Generators, Network Analyzers, and Bode Plotters.

Virtual instruments provide designers with an easy and intuitive method for interacting with their circuits asthey would in a testing or prototyping phase.

In addition to the provided virtual instruments, designers with familiar with National InstrumentsLabVIEW can create their own custom instruments from scratch. For example, one could create a custom noise generator to modelelectromagnetic interference.

Custom virtual instruments written in NI LabVIEW can also acquire real-world data and use the data to drivesimulations, and can send generated data to analog output hardware, allowing simulated data to control real-world devices. The LabVIEWdevelopment suite is required to create custom LabVIEW instruments, but not necessary to run existing LabVIEW based instruments.

To place a virtual instrument, select the desired instrument from the Instruments toolbar (Figure 1). To viewthe front panel of the instrument, double-click on the instrument icon. Make connections to the terminals of the instrument icon asyou would to any other component.

Multisim also provides designers with simulated benchtop instruments. These are instruments such as theTektronix TDS 2024 Oscilloscope. They will look and operate exactly according to the manufacturers’user manuals.

Instruments Toolbar

A single circuit can have multiple instruments attached to it, including (for most tiers) multiple instances ofthe same instrument. In addition, each circuit window can have its own set of instruments. Each instance of any instrument isconfigured and connected independently.

An overview of the more common instruments is included in this section. For more detailed information on how touse each instrument, consult the Multisim User Guide or helpfile.

Multimeter

Use the multimeter to measure AC or DC voltage or current, and resistance or decibel loss between two nodes in acircuit. The multimeter is auto-ranging, so a measurement range does not need to be specified. Its internal resistance and currentare preset to near-ideal values, which can be changed.

Multimeter Schematic Symbol
Multimeter Front Panel

Function generator

The function generator is a voltage source that supplies sine, triangular or square waves. It provides aconvenient and realistic way to supply stimulus signals to a circuit. The waveform can be changed and its frequency, amplitude,duty cycle and DC offset can be controlled. The function generator's frequency range is great enough to produce conventionalAC as well as audio- and radio-frequency signals.

The function generator has three terminals through which waveforms can be applied to a circuit. The commoncenter terminal provides a reference level for the signal.

Function Generator Schematic Symbol
Function Generator Front Panel

Oscilloscopes

Multisim includes several varieties of oscilloscopes. All of the scopes can be controlled like real-worldoscilloscopes. Horizontal timing and vertical voltages parameters can be adjusted. Triggering levels, and types are also selectable.Data from the Multisim-exclusive oscilloscopes is available in the Grapher after the interactive simulation has completed by selectingView/Grapher.

Multisim provides the following oscilloscopes:

  • 2-Channel.
  • 4-Channel.
  • Agilent 54622D Mixed Signal Oscilloscope.
  • Tektronix TDS 2024 Four Channel Digital Storage Oscilloscope.
Oscilloscope Schematic Symbol
Oscilloscope Front Panel
Tektronix Oscilloscope Schematic Diagram
Tektronix Oscilloscope Front Panel

Bode plotter

The bode plotter displays the relative phase or magnitude response of an input and output signal. This isespecially useful when characterizing the bandwidth of filter circuits.

Function Generator Schematic Symbol
Bode Plotter Front Panel

Spectrum analyzer

The spectrum analyzer is used to measure amplitude versus frequency. This instrument is capable of measuringa signal's power and frequency components, and helps determine the existence of harmonics in the signal.

The spectrum analyzer displays its measurements in the frequency domain rather than the time domain.Usually the reference frame in signal analysis is time. In that case, an oscilloscope is used to show the instantaneous value as afunction of time. Sometimes a sine waveform is expected but thesignal, rather than being a pure sinusoidal, has a harmonic on it. As a result, it is not possible to measure the waveform's level. Ifthe same signal is displayed on a spectrum analyzer, its amplitude is displayed, along with its frequency components, that is, itsfundamental frequency and any harmonics it may contain.

Spectrum Analyzer Schematic Symbol
Spectrum Analyzer Front Panel

Questions & Answers

the diagram of the digestive system
Assiatu Reply
How does twins formed
William Reply
They formed in two ways first when one sperm and one egg are splited by mitosis or two sperm and two eggs join together
Oluwatobi
what is genetics
Josephine Reply
Genetics is the study of heredity
Misack
how does twins formed?
Misack
What is manual
Hassan Reply
discuss biological phenomenon and provide pieces of evidence to show that it was responsible for the formation of eukaryotic organelles
Joseph Reply
what is biology
Yousuf Reply
the study of living organisms and their interactions with one another and their environments
AI-Robot
the study of living organisms and their interactions with one another and their environment.
Wine
discuss the biological phenomenon and provide pieces of evidence to show that it was responsible for the formation of eukaryotic organelles in an essay form
Joseph Reply
what is the blood cells
Shaker Reply
list any five characteristics of the blood cells
Shaker
lack electricity and its more savely than electronic microscope because its naturally by using of light
Abdullahi Reply
advantage of electronic microscope is easily and clearly while disadvantage is dangerous because its electronic. advantage of light microscope is savely and naturally by sun while disadvantage is not easily,means its not sharp and not clear
Abdullahi
cell theory state that every organisms composed of one or more cell,cell is the basic unit of life
Abdullahi
is like gone fail us
DENG
cells is the basic structure and functions of all living things
Ramadan
What is classification
ISCONT Reply
is organisms that are similar into groups called tara
Yamosa
in what situation (s) would be the use of a scanning electron microscope be ideal and why?
Kenna Reply
A scanning electron microscope (SEM) is ideal for situations requiring high-resolution imaging of surfaces. It is commonly used in materials science, biology, and geology to examine the topography and composition of samples at a nanoscale level. SEM is particularly useful for studying fine details,
Hilary
cell is the building block of life.
Condoleezza Reply
what is cell divisoin?
Aron Reply
Diversity of living thing
ISCONT
what is cell division
Aron Reply
Cell division is the process by which a single cell divides into two or more daughter cells. It is a fundamental process in all living organisms and is essential for growth, development, and reproduction. Cell division can occur through either mitosis or meiosis.
AI-Robot
What is life?
Allison Reply
life is defined as any system capable of performing functions such as eating, metabolizing,excreting,breathing,moving,Growing,reproducing,and responding to external stimuli.
Mohamed
Got questions? Join the online conversation and get instant answers!
Jobilize.com Reply

Get Jobilize Job Search Mobile App in your pocket Now!

Get it on Google Play Download on the App Store Now




Source:  OpenStax, Introduction to multisim schematic capture and spice simulation. OpenStax CNX. Sep 26, 2006 Download for free at http://cnx.org/content/col10369/1.3
Google Play and the Google Play logo are trademarks of Google Inc.

Notification Switch

Would you like to follow the 'Introduction to multisim schematic capture and spice simulation' conversation and receive update notifications?

Ask