<< Chapter < Page
  From matlab and simulink to real     Page 3 / 3
Chapter >> Page >

Select View ->Library Browser ->Signal Processing Blockset ->Filtering->Adaptive Filters.

Highlight “Adaptive Filters”. Drag-and-drop the “LMS Filter” block onto the model.

Adding an LMS Filter Block

Setting the lms filter parameters

The most critical variable in an LMS filter is the “Step size (mu)”.

If “mu” is too small, the filter has very fine resolution, but reacts too slowly to the audio signal.

If “mu” is too great, the filter reacts very quickly, but the error also remains large.

We will start with 0.005.

Setting the Parameter “Set size (mu)”

Adding a delay

From the “Signal Processing Blockset”, highlight “Signal Operations”. Drag-and-drop the “Delay” Since we are working with frames, the delay from “Discrete Components” library will not work! block onto the model.

Adding a Delay

Setting the delay parameters

Because we are working with frames of 64 samples, it is convenient configure the delay using frames. Double-click on the “Delay” block.

Change the “Delay units” to Frames.

Set the “Delay (frames)” to 1. This makes the delay 64 samples.

Setting the Delay Size

Adding a dip switch and led

So we can hear the difference without LMS denoising and with LMS noise reduction, we will use a DIP switch of the DSK6713.

Adding a Switch and LED

Select View ->Library Browser ->Embedded Target for TI C6000 DSP. Highlight “DSK6713 Board Support”.

Drag-and-drop the “Switch” block onto the model. Also drag-and-drop the “LED” block onto the model.

Dip switch settings

The DIP switch needs to be configured. Double-click on the “Switch” block.

Select all the boxes and set “Data type” to Integer. The “Sample time” should also be set to “–1”.

Setting up the DIP Switch Values

Adding a constant, switch and relational operator

We now need to setup a way to switch between straight through without noise reduction and with LMS noise reduction.

Select View ->Library Browser ->Simulink. Highlight “Commonly Used Blocks”.

Drag-and-drop a “Constant” onto the model.

Drag-and-drop a “Switch” block onto the model.

Drag-and-drop a “Relational Operator” block onto the model.

Selecting the Commonly Used Blocks

Setting the constant value

The switch values lie between 0 and 15. We will use switch values 0 and 1. Double-click on the “Constant” block. Set the “Constant value” to 1 and the “Sample time” to “inf”.

Setting the Echo Delay Gain

Setting the constant data type

Click on the “Signal Data Types” tab. Set the “Output data type mode” to “int16”. This is compatible with the DAC on the DSK6713.

Data Type Conversion to 16-bit Integer

Setting the relational operator type

Double click on the “Relational Operator” block. Change the “Relational operator” to “==”. Click on the “Signal Data Types” tab.

Changing the Relational Operator

Setting the relational operator data type

Set the “Output data type mode” to “Boolean”. Click on “OK”.

Changing the Output Data Type

Joining the blocks

Move the blocks and join them as shown in the Figure below.

Joining the Blocks

Returning to the parent system

From the Toolbar, select the “Up Arrow” icon. This returns you to the next higher level.

Returning to the Parent System

Building the model

Selecting real-time workshop

Select Tools ->Real-Time Workshop ->Build Model.

Building the Model

Frames displayed on model

When built, the single lines are replaced by double lines. This shows frames.

Frames

The completed model running on code composer studio

From the folders on the left, select the source code for the project.

The Completed Model Running in Code Composer Studio

Different settings on the dsk6713

Microphone straight through to loudspeakers

To check out the microphone and loudspeakers, set the DIP switches on the DSK6713 as follows:

Switch Position 0

The microphone is fed directly to the loudspeakers. There is no LMS noise reduction.

Switch position for lms noise reduction

To run the “LMS Noise Reduction” subsystem, set the DIP switch to 1.

Switch Position 1 for LMS Noise Reduction

Some things to try

You may wish to experiment with different settings. Here are some suggestions.

Experiment with lms filter settings

Change the value of “Step size (mu)” between 0.0001 and 0.5. This is the critical value.

Low values of mu give good resolution, but a slow reaction time.

High values of mu give less resolution, but faster reaction times.

Find the best value of mu for noise reduction on the TI DSK6713.

Configuring the LMS Filter Block Parameter

Experiment with lms filter settings

Try different value of “Filter Length”. What is the minimum value that will allow the filter to work correctly?

Change from lms filter to rls filter

Inside the “Adaptive Filters” are different LMS types. Which are suitable for LMS denoising and which are not?

Available Adaptive Filter Types

Figure 40 –

MATLAB and Simulink are registered trademarks of The MathWorks, Inc. See www.mathworks.com/trademarks for a list of additional trademarks. Other product or brand names may be trademarks or registered trademarks of their respective holders.

Questions & Answers

A golfer on a fairway is 70 m away from the green, which sits below the level of the fairway by 20 m. If the golfer hits the ball at an angle of 40° with an initial speed of 20 m/s, how close to the green does she come?
Aislinn Reply
cm
tijani
what is titration
John Reply
what is physics
Siyaka Reply
A mouse of mass 200 g falls 100 m down a vertical mine shaft and lands at the bottom with a speed of 8.0 m/s. During its fall, how much work is done on the mouse by air resistance
Jude Reply
Can you compute that for me. Ty
Jude
what is the dimension formula of energy?
David Reply
what is viscosity?
David
what is inorganic
emma Reply
what is chemistry
Youesf Reply
what is inorganic
emma
Chemistry is a branch of science that deals with the study of matter,it composition,it structure and the changes it undergoes
Adjei
please, I'm a physics student and I need help in physics
Adjanou
chemistry could also be understood like the sexual attraction/repulsion of the male and female elements. the reaction varies depending on the energy differences of each given gender. + masculine -female.
Pedro
A ball is thrown straight up.it passes a 2.0m high window 7.50 m off the ground on it path up and takes 1.30 s to go past the window.what was the ball initial velocity
Krampah Reply
2. A sled plus passenger with total mass 50 kg is pulled 20 m across the snow (0.20) at constant velocity by a force directed 25° above the horizontal. Calculate (a) the work of the applied force, (b) the work of friction, and (c) the total work.
Sahid Reply
you have been hired as an espert witness in a court case involving an automobile accident. the accident involved car A of mass 1500kg which crashed into stationary car B of mass 1100kg. the driver of car A applied his brakes 15 m before he skidded and crashed into car B. after the collision, car A s
Samuel Reply
can someone explain to me, an ignorant high school student, why the trend of the graph doesn't follow the fact that the higher frequency a sound wave is, the more power it is, hence, making me think the phons output would follow this general trend?
Joseph Reply
Nevermind i just realied that the graph is the phons output for a person with normal hearing and not just the phons output of the sound waves power, I should read the entire thing next time
Joseph
Follow up question, does anyone know where I can find a graph that accuretly depicts the actual relative "power" output of sound over its frequency instead of just humans hearing
Joseph
"Generation of electrical energy from sound energy | IEEE Conference Publication | IEEE Xplore" ***ieeexplore.ieee.org/document/7150687?reload=true
Ryan
what's motion
Maurice Reply
what are the types of wave
Maurice
answer
Magreth
progressive wave
Magreth
hello friend how are you
Muhammad Reply
fine, how about you?
Mohammed
hi
Mujahid
A string is 3.00 m long with a mass of 5.00 g. The string is held taut with a tension of 500.00 N applied to the string. A pulse is sent down the string. How long does it take the pulse to travel the 3.00 m of the string?
yasuo Reply
Who can show me the full solution in this problem?
Reofrir Reply
Got questions? Join the online conversation and get instant answers!
Jobilize.com Reply

Get Jobilize Job Search Mobile App in your pocket Now!

Get it on Google Play Download on the App Store Now




Source:  OpenStax, From matlab and simulink to real-time with ti dsp's. OpenStax CNX. Jun 08, 2009 Download for free at http://cnx.org/content/col10713/1.1
Google Play and the Google Play logo are trademarks of Google Inc.

Notification Switch

Would you like to follow the 'From matlab and simulink to real-time with ti dsp's' conversation and receive update notifications?

Ask